Inspiration

Tiles Installation – Guide

Wondering how to do tiles installation? What to do not to do it? We present 9 simple steps that divide you from the beautiful floor! Step 1. Prepare your floor. To start installing tiles, make sure that the floor is clean and dry. In places where humidity and water are more likely, eg in bathrooms or basements, you must pay special attention to it. It is necessary to thoroughly dry the room and then install the tiles in a short time. Step 2. Measure and mark your reference line. Use a spirit level, a masking tape and a pencil to mark the reference line. This is your point of reference for laying tiles so that they are simple and symmetrical. The reference line will allow you to place full tiles on each side of the line, then for tiles of the same width on the edges of the tiled area. Step 3. Mix the tile adhesive. Use the appropriate adhesive – for white tiles, use white adhesive to avoid discoloration. and with dark, gray tiles. Prepare an empty bucket, pour some water and add powdered glue. Stir until you get a texture similar to a toothpaste.If the solution is too liquid, add more glue, if it is too thick, add more water. Step 4. Temporarily place the tiles. A good idea is to spread some tiles dry to see how she would look at the finished floor. Before applying the adhesive, lay the tiles on the floor, using the selected reference line. Check that the tiles are evenly distributed on each side of the wall. If not, you need to correct the reference line. Step 5. Lay the tiles. Remember that an insulation mat, such as Schlüter DITRA, should be placed under the tiles. The mat must be suitable for the room conditions. Properly waterproof in bathrooms and usual rooms without moisture. Use a trowel to apply glue between the reference line and the next wall. Drag the adhesive trowel to increase the surface to which the tile will stick. Then apply a small amount of adhesive to the bottom edge of the tile running along the line of reference. Place the first tile on the surface and gently press it to align it with the line. Step 6. Place the cross between the tiles. Place the row of tiles between them and place the crosses between them. They will help to keep straight lines between the joints. Use two crosses for each side of the large tile. Insert the inter-all knuckles of the lying tiles. After the adhesive dries, the crosses can be easily removed with a pair of pliers. 7. Cut the tiles to the correct size. Measure the distance between the laid tile and the wall at both ends of the tile to ensure it is perpendicular to the wall. Mark the distance on both sides of the plate and draw a line. Place the tile in the saw and run the blade along the line. Press to break the tile along the line and place it on the floor. Repeat this process when measuring and cutting all tiles. If you plan to look them also on the wall, leave a small gap between the wall and tile on the floor. Step 8. Cut the tiles to make a drain (if necessary, if not, go to step 9). In this case, you have to cut the square in the tile to the drain . To do this, place the edge of the tile that you need to cut out on the one next to the drainage hole. Select the pads along one edge of the outflow length. Then turn the plate to the side, hold it above the tile and mark the width of the drain. Draw lines across the entire tile to indicate the length and width of the drain hole. Now, in a well-ventilated room, use a grinder to cut out the square for the drain. After cutting out the drain profile, cross-section of the transverse line to facilitate cutting. Place the cut tile above the drainage hole. Step 9. Finish laying the tiles. Continue cutting and installing the tiles to fill the floor surface. Use a spirit level to ensure that all tiles lie flat or at the right angle to enable water drainage. If any tiles are above or below the level of the tiles in the room, unplug them and add or remove the adhesive to level. Using a damp sponge, wipe off the adhesive that can flow between the tiles after pressing. After waiting 24-48 hours for the mortar to dry, carefully remove the crosses that are close to the surface. The scratch-offs of the mortar that was left on the plates with a screwdriver. Wipe the surface with a dry cloth. Apply the pre-grouting compound prepared earlier, do it diagonally and with a wide grip using a rubber float that does not scratch the surface. The grouting mass must fulfill all joints. Wait 30 minutes for the grout joint to dry, then soak the sponge in clean water and remove the grouting residue carefully. Done! Enjoy the perfect, self-made assembly of tiles!

Need tiles installation specialists? Click Here!



Leave a Reply

Your email address will not be published. Required fields are marked *