BathroomWaterproofing

How To Make a Shower Without a Shower Tray? Schlüter Shower Waterproofing.

Contemporary interior design trends recommend light, minimalist solutions. Modern decor provides a lot of space and light in the room. It is no different in modern bathroom designs. One of the most fashionable solutions today is a shower without a shower tray. Like everything, it has its pros and cons. However, the visual effect can convince even the most hardened follower of tradition. It is therefore worth considering what problems may arise during its installation. For valuable tips, visit the article that will explain how to make a shower without a shower tray. 

About what to remember before you decide? 

Even if you decide on a cabin without a shower tray, unfortunately it can not be installed everywhere. Before designing your bathroom, you need to consider many factors that can affect its final shape. It is worth knowing how to make a shower without a shower tray to assess whether the bathroom meets all the requirements.  

Shower cabins without a shower tray are best planned at the construction stage. If you are in the process of building your own home, think of a sufficiently thick ceiling. You can then run the entire installation inside. However, if you only want to renovate or refresh your bathroom, think about whether a shower cabin without a shower tray is the best solution for you. 

Its installation requires a properly profiled floor. This involves forging existing tiles and even the substrates under it. It is worth knowing that all this requires a significant financial outlay. Its installation will certainly pay off more when renovating a bathroom, where everything should be started from scratch. 

Preparing the place and choosing the right solution.

A shower without a shower tray has many advantages. Is a great solution for small bathrooms. With it, you can develop almost every corner of your bathroom. The shape of the shower is subject to many modifications depending on the needs. You can choose a square, triangular or rectangular shower, because you are not limited by a shower tray. In combination with a sliding entrance, it will allow you to make the most of the small space. In addition, a cabin without a shower tray surrounded by glass will not overwhelm the bathroom. It will become almost invisible, which will visually enlarge the room.  

You can use an existing recess to install the shower. You might as well add a wall that effectively separates the cabin from the rest of the bathroom. Here, however, remember that the recess should be large enough and provide the right amount of light. Glass blocks that let in light can also help you with this solution.  

Also, consider choosing a shower door. You can choose between classic doors that open to one side or swing doors. You can also choose to slide doors or opt out completely. So-called walk-in showers are very popular recently. The shower without a shower tray is separated by only one glass. Thanks to this, it is almost a part of it, blending into its walls. This creates a fantastic visual effect. This solution is also very helpful when children or disabled people use the bathroom.  

 If you want to create a more effective shield against splashing water, pay attention to the double segment 80 + 45 cm. You don’t have to worry that the bent wall will make it difficult to enter or lower the cabin. The shorter panel is movable in the 180 degree range, thanks to which you can tilt it in any direction, enabling a comfortable passage. 

Drain selection.

When planning the cabin assembly, it is worth choosing the appropriate drainage system. In this case, you need to consider both the bathroom’s design options, the size of the shower and visual effects. Currently, the most popular solutions are point or line drain.

  • The point outflow consists of a siphon, which is mounted in the floor and a grille installed at floor level. It is possible to cover the drain with a tile, which will reduce its visibility to a minimum. Point drains are usually mounted in the middle of the shower cubicle. It requires planning a 2% floor drop on each side of the drain. This type of drain is relatively small, which affects its water collection capacity. On a large surface, it is worth installing two drains to avoid flooding the floor. 
  • Linear drains have a larger water collection surface. They can be mounted on the wall or on the border of the shower cubicle. Here, too, a slope should be provided towards the drain, but this time only from one or two sides. The linear drainage system consists of: a shower channel built into the floor and a grate at the tile level. If we have little space for drainage while maintaining the slope, it is worth choosing a linear drainage system with a compact design – the shower channel is integrated with a siphon. Then the whole is about 8 cm thick instead of the standard 12 cm thick. 

In the event that the spray zone has a large surface, it is recommended to install two arc drains (thus reducing the likelihood of flooding). There is also a side drain. Then the entire sewage system is mounted in the wall and provides a suitable bleed after the entire shower. This solution will work if the thickness of the floor does not allow you to install another solution. Drywall will allow you to easily hide both the shower drain and the entire shower panel in the wall. However, remember that due to the high humidity in the bathroom, use Schlüter ® products to build this room. 

 When choosing the right drain, remember to make it more efficient than a shower faucet. Then you can be sure that all the water flows safely into the sewage system.

Take care of safety – moisture insulation – Schlüter Shower Waterproofing.

Proper moisture insulation not only protects your bathroom against moisture penetration under the tiles, but also the lower tier against flooding. This is an extremely important step in installing a shower without a shower tray.

Today, the floor is usually laid with a traditional sealing layer (roofing felt, bituminous coating) or foil made of synthetic resins. liquid foil, which is a less labor-intensive and faster solution. It should be applied to a dry concrete surface with a brush or putty knife. We apply layers one after the other until reaching a thickness of two millimeters. However, Schlüter Shower Waterproofing will be the best and most sensible solution for our bathroom.     

The edge of the line drain should be protected with a special polypropylene flange. Other places particularly exposed to flooding, such as the edges of walls and floors, as well as places where pipes exit from the wall, can be protected with a special sealing tape. Before laying the tiles, it is also worth protecting the wall under the spray with a sealant or tapes.

In Our opinion Schlüter shower waterproofing is the best solution because their products are of very high quality, and they always work. Here it will be useful to us Schlüter®-KERDI it is a pliable sheet-applied waterproofing membrane and vapor-retarder designed for the direct application of tile. KERDI is ideal for use in tiled showers, bathtub surrounds, residential steam showers, and other tile applications in wet areas.

We arrange the tiles!

There are two main points to consider when choosing the right tiles. The installation of a drain for a shower enclosure without a shower tray requires a 2% slope. To achieve this, large tiles will need to be cut properly, which can affect the visual effect. Smaller tiles already have a greater opportunity to cover a profiled floor. Mosaic tiles will completely hide the bleed. They can become a great solution especially in point outflow, which requires the so-called envelope bleed, i.e. from four sides. 

In the case of a linear drain, the tiles should protrude above the grate by about 2 mm. In addition, it is worth remembering that the shower tiles are non-slip. Poorly selected tiles after flooding can become very slippery and dangerous. Non-slip plates are usually marked with the symbol R9 to R13. Tiles of this type should be laid not only under the shower, but also on the entire floor surface. To make the bathing zone stand out, use decorative elements or tiles in a different shade.   

Choosing the right adhesive and grout is also important. Both products must have waterproof properties. Schlüter products also dominate here. For cabins without a shower tray, the best choice is a grout made of epoxy resin. It is flexible, does not crumble and provides protection against moisture with 100% efficiency. Unfortunately, it is a more expensive product than the usual waterproof joint.    

Installation of the cabin without a shower tray.

Now you know how to mount a shower enclosure without a shower tray. The most important stages of assembly have already been described. At the end, the only thing left is to install the glass separating the cabin. Here, the manufacturer’s instructions will certainly be useful. Each glass is placed in an aluminum frame, and also equipped with special gaskets and hinges. Depending on the manufacturer, it may be required to drill the appropriate holes in the aluminum frames to adjust the glass accordingly. At the end, there is a handle mounted. 

If your choice fell on the walk-in cabin model, just mount one windshield permanently. Then the time spent on installation is reduced by installing both handles and hinges. In addition, most walk-in models can be installed to the right or left – depending on your needs. It is worth refining the renovation of the bathroom by using an innovative form of shower. After the whole renovation process, there is nothing else but the joy of a warm, relaxing bath in the renovated bathroom